下载本文档
版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领
文档简介
1、Installation InstructionsP/N 7105320BLevel Kits for VersaBlueThese instructions describe the work required to retrofit a level display or level control in a VersaBlueR melter.ATTENTION: Allow only qualified personnel to perform the followingRequired tools:tasks. Follow the safety instructions here a
2、nd in the entire documen-Screwdriver and rubber hammertation.Various Allan keysPossible ConstellationsThere are three different constellations, which are coded in box 16 of the melter configuration code:L: Level display with level sensor (1)B: Level control with level sensor (1) and filling valve (3
3、) (Ni 120)P: Level control with level sensor (1), filling valve (3) and second level sensor (2) to prevent overfilling (Ni 120).C: Level control with level sensor (1) and filling valve (3) (Pt 100)D: Level control with level sensor (1), filling valve (3) and second level sensor (2) to prevent overfi
4、lling (Pt 100).F: Level control with level sensor (1)ATTENTION: Disconnect the melter from the line voltage before beginning retrofitting!Installing ComponentsNote: The illustrations indicate the component designations of the electrical parts. After installation, connect components as shown in the w
5、iring diagram.Only for B, C, D, and P:D Replace the assembly Tank lid and attach filling valve. The filling valve contains the heater cartridge (21E5) and the temperature sensor (21B2). The solenoid valve is triggered via the interface (XS3).D Install additional power supply (71T2) in the electrical
6、 cabinet. The installation position depends on the unit type.D Install interface (XS3).For all constellations:D Install the level sensor (221B2) in the tank collar. For cable duct: Punch out the perforated plate in the tank collar with a screwdriver and rubber hammer, working from the inside to the
7、outside.D Install the evaluator (221A1) in the electrical cabinet. Also refer to the melter manual, section Repair (for F: separate manual for the evaluator).Only for D and P:D Install the second level sensor (222B2) in the tank collar.D Install the second evaluator (222A1) in the electrical cabinet
8、.1 221B22 222B23 21E5, 21B2XS3Cable duct221A1222A1V50 / V100V12 / V2571T2ContinueReplacing ID PlateThe configuration code of the melter changes after retrofitting.1.Remove the old ID plate from the melter and replace it with the ID plate included in the retrofitting kit.Entering Configuration Code1.
9、2.Reconnect the power supply and switch on the melter with the main switch.Press the button Configuration code input (Refer to illustration).3.Enter the melter configuration code twice. Enter the code for the constellation being used in the 16th position (L, B, P, C, D or F).If the two codes entered
10、 are the same, the button to confirm is enabled. The configuration is saved on the memory card.Adjusting EvaluatorOnly for F:D Refer to the separate manual for the evaluatorOnly for B, C, D, L, P:D Refer to the melter manual, section Repair.Other Installation and OperationRefer to the melter manual
11、for information on:D Connecting the filling valve (not for L)D Level configuration.Configuration CodeInputInstallationshinweiseP/N 7105320BFllstand-Kits fr VersaBlueDiese Installationshinweise beschreiben die Arbeiten zum Nachrsten einer Fllstandanzeige oder Fllstandsteuerung in ein VersaBlueR Schme
12、lzgert.ACHTUNG: Alle folgenden Ttigkeiten nur von qualifiziertemErforderliches Werkzeug:Personal ausfhren lassen. Sicherheitshinweise hier und in derSchraubendreher und Gummihammergesamten Dokumentation befolgen.Diverse InbusschlsselAusbaustufenEs existieren unterschiedliche Ausbaustufen, die im Kon
13、figurations-kode des Schmelzgertes, Box 16, folgendermaen kodiert sind:L: Fllstandanzeige mit Fllstandsensor (1)B: Fllstandsteuerung mit Fllstandsensor (1), und Befllventil (3)(Ni 120)P: Fllstandsteuerung mit Fllstandsensor (1), Befllventil (3) und zweitem Fllstandsensor (2) fr berfllschutz (Ni 120)
14、C: Fllstandsteuerung mit Fllstandsensor (1), und Befllventil (3)(Pt 100)D: Fllstandsteuerung mit Fllstandsensor (1), Befllventil (3) und zweitem Fllstandsensor (2) fr berfllschutz (Pt 100)F: Fllstandsteuerung mit Fllstandsensor (1)Komponenten einbauenACHTUNG: Vor Beginn der Umbauarbeiten Schmelzgert
15、 von der Netzspannung trennen!Hinweis: In den Abbildungen sind die Betriebsmittel-Kennzeichen der elektrischen Komponenten angegeben. Komponenten nach Ein-bau gem Schaltplan verdrahten.Nur bei B, C, D und P:D Baugruppe Tankdeckel austauschen und Befllventil montieren. Das Befllventil enthlt Heizpatr
16、one (21E5) und Temperatursensor (21B2). Das Magnetventil wird ber Schnittstelle (XS3) angesteuert.D Zustzliche Stomversorgung (71T2) im Schaltschrank einbauen. Einbauort je nach Gertetyp.D Schnittstelle (XS3) einbauen.Bei allen Ausbaustufen:D Fllstandsensor (221B2) im Kragen des Tanks montieren. Fr
17、Kabeldurchfhrung: Vorgestanztes Blech im Kragen des Tanks mit Schraubendreher und Gummihammer von innen nach auen ausbrechen und entfernen.D Auswerteeinheit (221A1) im Schaltschrank einbauen. Siehe auch Betriebsanleitung des Schmelzgertes, Abschnitt Reparatur (bei F: separate Betriebsanleitung der A
18、uswerteeinheit)Zustzlich bei D und P:D Zweiten Fllstandsensor (222B2) im Kragen des Tanks montieren.D Zweite Auswerteeinheit (222A1) im Schaltschrank einbauen.1 221B22 222B23 21E5, 21B2XS3Kabeldurchfhrung221A1222A1V50 / V100V12 / V2571T2WeiterTypenschild auswechselnDurch den Umbau hat sich der Konfi
19、gurationskode des Schmelzgertes gendert.1.Altes Typenschild am Schmelzgert entfernen und durch das Typenschild ersetzen, das mit dem Kit geliefert wurde.Konfigurationskode eingeben1.2.Netzspannung wieder herstellen und Schmelzgert am Hauptschalter einschalten.Taste Konfigurationskode Eingabe bettigen (siehe Abbildung).3.Konfigurat
温馨提示
- 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
- 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
- 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
- 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
- 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
- 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
- 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
最新文档
- 税法:消费税法测试题(三)
- 水文勘测中级工考试资料(题库版)
- 水文勘测初级工考点(强化练习)
- 2024三方买卖协议
- 2024商标使用权转让合同范本
- 2024医药咨询服务合同
- 2024个人与公司买卖合同模板
- 2024全新数据分析服务合同下载
- 携程旅游运营模式分析报告总结
- 2024年防疫情工作总结怎么写篇
- 二次结构砌筑施工技术质量要求
- T∕CCOA 4-2019 干米粉
- 隧道维修加固项目施工方案
- 世界银行新建火力发电厂导则译文
- 端午节的由来PPT
- 小壁虎借尾巴PPT课件
- 苏教版小学数学四年级下册 第6单元运算律2应用加法运算律进行简便计算 课件
- 小学道德与法治生活化探究教研课题论文开题结题中期研究报告(反思经验交流)
- 无线调车机车信号与监控系统(STP)
- 社会团体负责人备案表(共6页)
- 垃圾分类宣传小册子电子版
评论
0/150
提交评论