版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领
文档简介
1、Overview of VDI 2230,An Introduction to the Calculation Method for Determining the Stress in a Bolted Joint,Important Note,This summary of the VDI 2230 Standard is intended to provide a basic understanding of the method. Readers who wish to put the standard to use are urged to refer to the complete
2、standard that contains all information, figures, etc.,Definitions,Covers high-duty bolted joints with constant or alternating loads Bolted joints are separable joints between two or more components using one or more bolts Joint must fulfill its function and withstand working load,Aim of Calculation,
3、Determine bolt dimension allowing for: Strength grade of the bolt Reduction of preload by working load Reduction of preload by embedding Scatter of preload during tightening Fatigue strength under an alternating load Compressive stress on clamped parts,1. Range of Validity,Steel Bolts M4 to M39 Room
4、 Temperature,2. Choice of Calculation Approach,Dependent upon geometry Cylindrical single bolted joint Beam connection Circular plate Rotation of flanges Flanged joint with plane bearing face,Cylindrical Single Bolted Joint,Axial force, FA Transverse force, FQ Bending moment, MB,Beam Geometry, Ex. 1
5、,Axial force, FA Transverse force, FQ Moment of the plane of the beam, MZ,Beam Geometry, Ex. 2,Axial force, FA Transverse force, FQ Moment of the plane of the beam, MZ,Rotation of Flanges,Axial force, FA (pipe force) Bending moment, MB Internal pressure, p,Flanged Joint with Plane Bearing Face, Ex.
6、1,Axial force, FA (pipe force) Torsional moment, MT Moment, MB,Flanged Joint with Plane Bearing Face, Ex. 2,Axial force, FA (pipe force) Transverse force, FQ Torsional moment, MT Moment, MB,Flanged Joint with Plane Bearing Face, Ex. 3,Axial force, FA (pipe force) Transverse force, FQ Torsional momen
7、t, MT Moment, MB,3. Analysis of Force and Deformation,Optimized by means of thorough and exact consideration of forces and deformations including: Elastic resilience of bolt and parts Load and deformation ratio for parts in assembled state and operating state,4. Calculation Steps,Begins with externa
8、l working load, FB Working load and elastic deformations may cause: Axial force, FA Transverse force, FQ Bending Moment, MB Torque moment, MT,Determining Bolt Dimensions,Once working load conditions are known allow for: Loss of preload to embedding Assembly preload reduced by proportion of axial bol
9、t force Necessary minimum clamp load in the joint Preload scatter due to assembly method,Calculation Step R1,Estimation of bolt diameter, d Estimation of clamping length ratio, lK/d Estimation of mean surface pressure under bolt head or nut area, pG If pG is exceeded, joint must be modified and lK/d
10、 re-determined,Calculation Step R2,Determination of tightening factor, aA, allowing for: Assembly method State of lubrication Surface condition,Calculation Step R3,Determination of required average clamping load, Fkerf, as either: Clamping force on the opening edge with eccentrically acting axial fo
11、rce, FA Or Clamping force to absorb moment MT or transverse force component, FQ,Calculation Step R4,Determination of load factor, F, including: Determination of elastic resilience of bolt, dS Evaluation of the position of load introduction, n*lK Determination of elastic resilience of clamped parts,
12、dP Calculation of required substitutional cross-section, Aers,Calculation Step R5,Determination of loss of preload, FZ, due to embedding Determination of total embedding,Calculation Step R6,Determination of bolt size and grade For tightening within the elastic range, select bolt for which initial cl
13、amping load is equal to or greater than maximum initial clamping load due to scatter in assembly process For tightening to yield, select bolt for which 90% of initial clamping load is equal to or greater than minimum initial clamping load due to scatter in assembly process,Calculation Step R7,If cha
14、nges in bolt or clamping length ratio, lK/d, are necessary, repeat Steps R4 through R6,Calculation Step R8,Check that maximum permissible bolt force is not exceeded,Calculation Step R9,Determine alternating stress endurance of bolt Allow for bending stress in eccentric load applications Obtain appro
15、ximate value for permissible stress deviation from tables If not satisfactory, use bolt with larger diameter or greater endurance limit Consider bending stress for eccentric loading,Calculation Step R10,Check surface pressure under bolt head and nut bearing area Allow for chamfering of hole in deter
16、mining bearing area Tables provide recommendations for maximum allowable surface pressure If using tightening to or beyond yield, modify calculation,5. Influencing Factors,Allow for factors depending upon: Material and surface design of clamped parts Shape of selected bolts and nuts Assembly conditi
17、ons,Strength of the Bolt,Stress caused by: Torsional and axial stresses during tightening Working load Should not exceed yield load,Minimum Thread Engagement,Depends upon: Thread form, pitch, tolerance, and diameter Form of the nut (wrenching width) Bolt hole Strength and ductility of bolt and nut m
18、aterials Type of stress (tensile, torsional, bending) Friction coefficients Number of tightenings,Thread Shear Strength,Bolt-Nut Strength Matching Number for strength grade of nut is equivalent to first number of strength grade of bolt,Calculation of Required Nut Height,Allows for geometry and mecha
19、nical properties of joint elements Predicts type of failure caused by overloading Considers: Dimensional values (tensile cross-section of bolt thread, thread engagement length, etc.) Thread form & nut form Bolt clearance hole,Bolt Head Height,Ensures that failure will occur in free loaded thread sec
20、tion or in the shank Highest tensile stress in thread Highest tensile stress in bolt head,Surface Pressure at Bolt Head & Nut Bearing Areas,Calculation determines surface pressure capable of causing creep resulting in loss of preload Surface pressure due to maximum load should not exceed compressive
21、 yield point of clamped material,Tightening Factor, Alpha A,Allowance must be made for torsional stress caused by pitch and thread friction, and axial tensile stress Scatter in friction coefficients and errors in method of controlling preload create uncertainty in level of tensile and torsional stress Tightening factor, aA, reflects amount of required “over-design”,Fatigue Strength,Design modifications to improve endurance limit of joint Increase preload Reduce pitch of screw thread Reduction of modulus of nut material elasticity Increase thread engagement,Fatigue Strength -Continued,Desi
温馨提示
- 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
- 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
- 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
- 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
- 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
- 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
- 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
最新文档
- 牛津苏教四下Unit1Astudent之四市公开课一等奖省赛课微课金奖课件
- 中考地理系统复习成绩基石综合检测卷(二)市赛课公开课一等奖省名师获奖课件
- Unit2-WritingaLetterofInvitation市公开课一等奖省赛课微课金奖课
- 7b-unit6-Reading市公开课一等奖省赛课微课金奖课件
- 复习存储器管理市公开课特等奖市赛课微课一等奖课件
- 变化率问题公开课省公开课一等奖全国示范课微课金奖课件
- 七年级语文下册第二单元7第一千个球课件省公开课一等奖新名师获奖课件
- 高考英语复习Module4WhichEnglish市赛课公开课一等奖省名师获奖课件
- 大学固体废弃物的处理方法经典-固体废物的微生物分解省公开课金奖全国赛课一等奖微课获奖课件
- 2024年北京四中高二化学化学反应速率和化学平衡(高二)1化学反应速率
- 建筑工程检测项目代表批量取样方法及数量
- 消防各部位上墙制度内容及制作张贴规范
- 隧道开挖作业台车计算书
- IATF-16949质量管理体系五大工具培训课件
- 第六单元第三课保护个人隐私课件(共21张PPT)
- 30万吨年煤制甲醇变换工段初步设计
- 部编版小学道德与法治(五四制)五年级上册11《屹立在世界的东方》第三课时《自力更生-扬眉吐气》教学设计
- 小区排水管网改造工程施工组织设计方案
- 二十四节气立夏PPT
- 411同分母分数加减法课件
- 铜及铜合金的焊接汇总
评论
0/150
提交评论