外文原文.pdf_第1页
外文原文.pdf_第2页
外文原文.pdf_第3页
外文原文.pdf_第4页
外文原文.pdf_第5页
已阅读5页,还剩8页未读 继续免费阅读

下载本文档

版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领

文档简介

Int J Adv Manuf Technol (2003) 21:807819Ownership and Copyright 2003 Springer-Verlag London LimitedA Parametric-Controlled Cavity Layout Design System for aPlastic Injection MouldM. L. H. Low and K. S. LeeDepartment of Mechanical Engineering, National University of Singapore, SingaporeToday, the time-to-market for plastic products is becomingshorter, thus the lead time available for making the injectionmould is decreasing. There is potential for timesaving in themould design stage because a design process that is repeatablefor every mould design can be standardised. This paperpresents a methodology for designing the cavity layout forplastic injection moulds by controlling the geometrical para-meters using a standardisation template. The standardisationtemplate for the cavity layout design consists of the configur-ations for the possible layouts. Each configuration of the layoutdesign has its own layout design table of all the geometricalparameters. This standardisation template is pre-defined at thelayout design level of the mould assembly design. This ensuresthat the required configuration can be loaded into the mouldassembly design very quickly, without the need to redesign thelayout. This makes it useful in technical discussions betweenthe product designers and mould designers prior to the manu-facture of the mould. Changes can be made to the 3D cavitylayout design immediately during the discussions, thus savingtime and avoiding miscommunication. This standardisation tem-plate for the cavity layout design can be customised easily foreach mould making company to their own standards.Keywords: Cavity layout design; Geometrical parameters;Mould assembly; Plastic injection mould design; Standardis-ation template1. IntroductionPlastic injection moulding is a common method for the massproduction of plastic parts with good tolerances. There are twomain items that are required for plastic injection moulding.They are the injection-moulding machine and the injectionmould. The injection-moulding machine has the mould mountedCorrespondence and offprint requests to: K. S. Lee, Department ofMechanical Engineering, National University of Singapore, 10 KentRidge Crescent, Singapore 119260. E-mail address: .sgReceived 8 January 2002Accepted 16 April 2002on it and provides the mechanism for molten plastic transferfrom the machine to the mould, clamping the mould by theapplication of pressure and the ejection of the formed plasticpart. The injection mould is a tool for transforming the moltenplastic into the final shape and dimensional details of theplastic part. Today, as the time-to-market for plastic parts isbecoming shorter, it is essential to produce the injection mouldin a shorter time.Much work had been done on applying computer techno-logies to injection mould design and the related field. Knowl-edge-based systems (KBS) such as IMOLD 1,2, IKMOULD3, ESMOLD 4, the KBS of the National Cheng KangUniversity, Taiwan 5, the KBS of Drexel University 6, etc.were developed for injection mould design. Systems such asHyperQ/Plastic 7, CIMP 8, FIT 9, etc. are developed forthe selection of plastic materials using a knowledge-basedapproach. Techniques have also been developed for partingdesign in injection moulding 1012.It has been observed that although mould-making industriesare using 3D CAD software for mould design, much time iswasted in going through the same design processes for everyproject. There is great potential for timesaving at the moulddesign stage if the repeatable design processes can be standard-ised to avoid routine tasks. A well-organised hierarchical designtree in the mould assembly is also an important factor 13,14.However, little work has been done in controlling the para-meters in the cavity layout design; thus this area will be ourmain focus. Although there are many ways of designing thecavity layout 15,16, mould designers tend to use only conven-tional designs, thus there is a need to apply standardisation atthe cavity layout design level.This paper presents a methodology for designing the cavitylayout for plastic injection moulds by controlling the parametersbased on a standardisation template. First, a well-organisedmould assembly hierarchy design tree had to be established.Then, the classification of the cavity layout configuration hadto be made to differentiate between those with standard con-figurations and those with non-standard configurations. Thestandard configurations will be listed in a configuration databaseand each configuration has its own layout design table thatcontrols its own geometrical parameters. This standardisation808 M. L. H. Low and K. S. LeeFig. 1. Front insert (cavity) and back insert (core).template is pre-defined at the layout design level of the mouldassembly design.2. Cavity Layout Design for a PlasticInjection MouldAn injection mould is a tool for transforming molten plasticinto the final shape and dimensional details of a plastic part.Thus, a mould contains an inverse impression of the final part.Most of the moulds are built up of two halves: the front insertand the back insert. In certain mould-making industries, thefront insert is also known as the cavity and the back insert isknown as the core. Figure 1 shows a front insert (cavity) anda back insert (core). Molten plastic is injected into theimpression to fill it. Solidification of the molten plastic thenforms the part. Figure 2 shows a simple two-plate mouldassembly.Fig. 2. A simple mould assembly.2.1 Difference Between a Single-Cavity and aMulti-Cavity MouldVery often, the impression in which molten plastic is beingfilled is also called the cavity. The arrangement of the cavitiesis called the cavity layout. When a mould contains more thanone cavity, it is referred to as a multi-cavity mould. Figures 3(a)and 3(b) shows a single-cavity mould and a multi-cavity mould.A single-cavity mould is normally designed for fairly largeparts such as plotter covers and television housings. For smallerparts such as hand phone covers and gears, it is always moreeconomical to design a multi-cavity mould so that more partscan be produced per moulding cycle. Customers usually deter-mine the number of cavities, as they have to balance theinvestment in the tooling against the part cost.2.2 Multi-Cavity LayoutA multi-cavity mould that produces different products at thesame time is known as a family mould. However, it is notusual to design a mould with different cavities, as the cavitiesmay not all be filled at the same time with molten plastic ofthe same temperature.On the other hand, a multi-cavity mould that produces thesame product throughout the moulding cycle can have a bal-anced layout or an unbalanced layout. A balanced layout isone in which the cavities are all uniformly filled at the sametime under the same melt conditions 15,16. Short mouldingcan occur if an unbalanced layout is being used, but this canbe overcome by modifying the length and cross-section of therunners (passageways for the molten plastic flow from thesprue to the cavity). Since this is not an efficient method, itis avoided where possible. Figure 4 shows a short mouldingsituation due to an unbalanced layout.A balanced layout can be further classified into two categor-ies: linear and circular. A balanced linear layout can accommo-date 2, 4, 8, 16, 32 etc. cavities, i.e. it follows a 2nseries. Abalanced circular layout can have 3, 4, 5, 6 or more cavities,but there is a limit to the number of cavities that can beaccommodated in a balanced circular layout because of spaceconstraints. Figure 5 shows the multi-cavity layouts that havebeen discussed.3. The Design ApproachThis section presents an overview of the design approach forthe development of a parametric-controlled cavity layout designsystem for plastic injection moulds. An effective workingmethod of mould design involves organising the various subas-semblies and components into the most appropriate hierarchydesign tree. Figure 6 shows the mould assembly hierarchydesign tree for the first level subassembly and components.Other subassemblies and components are assembled from thesecond level onwards to the nth level of the mould assemblyhierarchy design tree. For this system, the focus will be madeonly on the “cavity layout design”.A Cavity Layout Design System 809Fig. 3. (a) A single cavity mould. (b) A multi-cavity mould.Fig. 4. Short moulding in an unbalanced layout.3.1 Standardisation ProcedureIn order to save time in the mould design process, it isnecessary to identify the features of the design that are com-monly used. The design processes that are repeatable for everymould design can then be standardised. It can be seen fromFig. 7 that there are two sections that interplay in the stan-dardisation procedure for the “cavity layout design”: componentassembly standardisation and cavity layout configuration stan-dardisation.810 M. L. H. Low and K. S. LeeFig. 5. Multi-cavity layouts.Fig. 6. Mould assembly hierarchical design tree.Fig. 7. Interplay in the standardization procedure.3.1.1 Component Assembly StandardisationBefore the cavity layout configuration can be standardised,there is a need to recognise the components and subassembliesthat are repeated throughout the various cavities in the cavitylayout. Figure 8 shows a detailed “cavity layout design” hier-archy design tree. The main insert subassembly (cavity) in theFig. 8. Detailed “cavity layout design” hierarchical design tree.second level of the hierarchy design tree has a number ofsubassemblies and components that are assembled directly toit from the third level onwards of the hierarchy design tree.They can be viewed as primary components and secondarycomponents. Primary components are present in every moulddesign. The secondary components are dependent on the plasticpart that is to be produced, so they may or may not be presentin the mould designs.As a result, putting these components and subassembliesdirectly under the main insert subassembly, ensures that everyrepeatable main insert (cavity) will inherit the same subas-semblies and components from the third level onwards of thehierarchy design tree. Thus, there is no need to redesignsimilar subassemblies and components for every cavity in thecavity layout.3.1.2 Cavity Layout Configuration StandardisationIt is necessary to study and classify the cavity layout configur-ations into those that are standard and those that are non-standard. Figure 9 shows the standardisation procedure of thecavity layout configuration.A cavity layout design, can be undertaken either as a multi-cavity layout or a single-cavity layout, but the customersalways determine this decision. A single-cavity layout is alwaysconsidered as having a standard configuration. A multi-cavitymould can produce different products at the same time or theA Cavity Layout Design System 811Fig. 9. Standardisation procedure of the cavity layout configuration.same products at the same time. A mould that producesdifferent products at the same time is known as a familymould, which is a non-conventional design. Thus, a multi-cavity family mould has a non-standard configuration.A multi-cavity mould that produces the same product cancontain either a balanced layout design or an unbalanced layoutdesign. An unbalanced layout design is seldom used and, as aresult, it is considered to possess a non-standard configuration.However, a balanced layout design can also encompass eithera linear layout design or a circular layout design. This dependson the number of cavities that are required by the customers.It must be noted, however, that a layout design that has anyother non-standard number of cavities is also classified ashaving a non-standard configuration.After classifying those layout designs that are standard, theirdetailed information can then be listed into a standardisationtemplate. This standardisation template is pre-defined in thecavity layout design level of the mould assembly design andsupports all the standard configurations. This ensures that therequired configuration can be loaded very quickly into themould assembly design without the need to redesign the layout.3.2 Standardisation TemplateIt can be seen from Fig. 10 that there are two parts in thestandardisation template: a configuration database and a layoutFig. 10. The standardization template.design table. The configuration database consists of all thestandard layout configurations, and each layout configurationhas its own layout design table that carries the geometricalparameters. As mould-making industries have their own stan-dards, the configuration database can be customised to takeinto account those designs that are previously considered asnon-standard.3.2.1 Configuration DatabaseA database can be used to contain the list of all the differentstandard configurations. The total number of configurations inthis database corresponds to the number of layout configur-ations available in the cavity layout design level of the moulddesign assembly. The information listed in the database is theconfiguration number, type, and the number of cavities. Table 1shows an example of a configuration database. The configur-ation number is the name of each of the available layoutconfigurations with the corresponding type and number ofcavities. When a particular type of layout and number ofcavities is called for, the appropriate layout configuration willbe loaded into the cavity layout design.3.2.2 Layout Design TableEach standard configuration listed in the configuration databasehas its own layout design table. The layout design tablecontains the geometrical parameters of the layout configurationand is independent for every configuration. A more complexlayout configuration will have more geometrical parameters tocontrol the cavity layout.Figures 11(a) and 11(b) show the back mould plate (coreplate) with a big pocket and four small pockets for assemblingthe same four-cavity layout. It is always more economical andeasier to machine a large pocket than to machine individualsmaller pockets in a block of steel. The advantages of machin-ing a large pocket are:812 M. L. H. Low and K. S. LeeFig. 11. The back mould plate with pocketing.Table 1. Sample of the configuration database.Configuration number Type Number of cavitiesS01 Single 1L02 Linear 2L04 Linear 4L08 Linear 8L16 Linear 16L32 Linear 32L64 Linear 64C03 Circular 3C04 Circular 4C05 Circular 5C06 Circular 61. More space between the cavities can be saved, thus asmaller block of steel can be used.2. Machining time is faster for creating one large pocketcompared to machining multiple small pockets.3. Higher accuracy can be achieved for a large pocket thanfor multiple smaller pockets.As a result, the default values of the geometrical parametersin the layout design table results in there being no gap betweenthe cavities. However, to make the system more flexible, thedefault values of the geometrical parameters can be modifiedto suit each mould design where necessary.3.3 Geometrical ParametersThere are three variables that establish the geometrical para-meters:1. Distances between the cavities (flexible). The distancesbetween the cavities are listed in the layout design tableand they can be controlled or modified by the user. Thedefault values of the distances are such that there are nogaps between the cavities.2. Angle of orientation of the individual cavity (flexible). Theangle of orientation of the individual cavity is also listedin the layout design table which the user can change. Fora multi-cavity layout, all the cavities have to be at the sameangle of orientation as indicated in the layout design table.If the angle of orientation is modified, all the cavities willbe rotated by the same angle of orientation without affectingthe layout configuration.3. Assembly mating relationship between each cavities (fixed).The orientation of the cavities with respect to each other ispre-defined for each individual layout configuration and iscontrolled by the assembly mating relationship betweencavities. This is fixed for every layout configuration unlessit is customised.Figure 12 shows an example of a single-cavity layout con-figuration and its geometrical parameters. The origin of themain insert/cavity is at the centre. The default values of X1and Y1 are zero so that the cavity is at the centre of thelayout (both origins overlap each other). The user can changethe values of X1 and Y1, so that the cavity can be offset appro-priately.Figure 13 shows an example of an eight-cavity layout con-figuration and its geometrical parameters. The values of X andY are the dimensions of the main insert/cavity. By default, thevalues of X1 and X2 are equal to X, the value of Y1 is equalto Y, and thus there is no gap between the cavities. The valuesof X1, X2, and Y1 can be increased to take into account thegaps between the cavities in the design. These values are listedin the layout design table.If one of the cavities has to be oriented by 90, the rest ofthe cavities will be rotated by the same angle, but the layoutdesign remains the same. The user is able to rotate the cavitiesby changing the parameter in the layout design table. Theresultant layout is shown in Fig. 14.Fig. 12. Single-cavity layout configuration and geometrical parameters.A Cavity Layout Design System 813Fig. 13. Eight-cavity layout configuration and geometrical parameterswithout cavity rotation.Fig. 14. Eight-cavity layout configuration and geometrical parameterswith cavity rotation.A complex cavity layout configuration, which has moregeometrical parameters, must make use of equation to relatethe parameters.4. System ImplementationA prototype of the parametric-controlled cavity layout designsystem for a plastic injection mould has been implementedusing a Pentium III PC-compatible as the hardware. Thisprototype system uses a commercial CAD system (SolidWorks2001) and a commercial database system (Micr

温馨提示

  • 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
  • 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
  • 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
  • 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
  • 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
  • 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
  • 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

评论

0/150

提交评论