E1对接测试.doc

R2621dis ver Copyright Notice: All rights reserved (Jul 31 2004). Without the owners prior written consent, no decompiling or reverse-engineering shall be allowed. Huawei Versatile Routing Platform Software VRP (R) software, Version 1.74 Release 0108 Copyright (c) 1997-2003 HUAWEI TECH CO., LTD. Quidway R2620 uptime is 0 days 0 hours 40 minutes 7 seconds System returned to ROM by power-on. Quidway R2620 with 1 MPC 8240 Processor Router serial number is 8040C5ED0A394C6C 32M bytes SDRAM 8192K bytes Flash Memory 0K bytes NVRAM Config Register points to FLASH Hardware Version is MTR 1.1 CPLD Version is CPLD 2.0 Bootrom Version is 7.03 AUX AUX Hardware Version is 1.0, Driver Version is 1.0 LAN 1FE Hardware Version is 2.0, Driver Version is 2.0 WAN SAB Hardware Version is 1.0, Driver Version is 1.0 Slot 0 2E1-F Hardware Version is 1.0, Driver Version is 1.0, Cpld Version is 1.0 Slot 1 2cE1 Hardware Version is 1.1, Driver Version is 1.0 R2631Edis ver Copyright Notice: All rights reserved (Jun 16 2004). Without the owners prior written consent, no decompiling nor reverse-engineering shall be allowed. Huawei-3Com Versatile Routing Platform Software VRP(R) software, Version 3.30, Release 0006 Copyright (c) 2003-2004 Hangzhou Huawei-3Com Tech. Co.,Ltd. All rights reserved. Copyright (c) 2000-2003 Huawei Tech. Co.,Ltd. All rights reserved. Quidway Series Router 2631 uptime is 0 week, 0 day, 1 hour, 21 minutes CPU type: PowerPC 8240 200MHz 64M bytes SDRAM Memory 8M bytes Flash Memory 128K bytes NvRAM Memory Pcb Version:1.1 Logic Version:3.0 BootROM Version:9.05 SLOT 1 2FE (Hardware)2.0, (Driver)2.0, (Cpld)0.0 SLOT 2 RTB22SA (Hardware)1.1, (Driver)1.4, (Cpld)0.0 SLOT 3 1cE1 (Hardware)1.0, (Driver)1.0, (Cpld)0.0 R2621 E1-F (不能划分时隙,不能配置,默认1-31时隙捆绑)和R2631E E1模式对接配置: R2631Econtroller E1 3/0 using e1interface Serial3/0:0 link-protocol ppp ip address 5.6.7.8 255.255.255.0R2621无E1-F配置选项interface Serial2 link-protocol ppp ip address 5.6.7.10 255.255.255.0 端口状态显示R2631Edis inter serial 3/0:0 Serial3/0:0 current state :UP Line protocol current state :DOWN Description : Serial3/0:0 Interface The Maximum Transmit Unit is 1500, Hold timer is 10(sec) Derived from E1 3/0, Unframed mode, baudrate is 2048000 bps32个时隙非成帧 Internet Address is 5.6.7.8/24 Link layer protocol is PPP LCP stopped Output queue : (Urgent queue : Size/Length/Discards) 0/50/0 Output queue : (Protocol queue : Size/Length/Discards) 0/500/0 Output queue : (FIFO queuing : Size/Length/Discards) 0/75/0 Last 300 seconds input rate 0.00 bytes/sec, 0.00 packets/sec Last 300 seconds output rate 2.09 bytes/sec, 0.11 packets/sec Input: 0 packets, 0 bytes 0 broadcasts, 0 multicasts 0 errors, 0 runts, 0 giants 0 CRC, 0 align errors, 0 overruns 0 dribbles, 0 aborts, 0 no buffers 0 frame errors Output:91 packets, 1638 bytes 0 errors, 0 underruns, 0 collisions 0 deferred R2621dis int serial 2 Serial2 current state:down, line protocol current state:down The Maximum Transmit Unit is 1500 Internet Address is 5.6.7.10(24) physical layer is E1-F, baudrate is 1984000 bps Link-protocol is PPP LCP initial, IPCP initial, IPXCP initial, CCP initial, BRIDGECP initial Input queue : (size/max/drops) 0/50/0 FIFO queueing: FIFO (Outbound queue:Size/Length/Discards) FIFO: 0/75/0 Last 5 minutes input rate 0.00 bytes/sec, 0.00 packets/sec Last 5 minutes output rate 0.00 bytes/sec, 0.00 packets/sec Input: 437 packets, 11912 bytes 0 broadcasts, 0 multicasts 37 errors, 0 runts, 0 giants 32 CRC,1 frame errors, 4 overrunners 0 aborted sequences 0 no buffers 0 packets with dribble condition detected Output:576 packets, 9568 bytes 0 broadcasts, 0 multicasts 0 errors, 0 underruns, 0 collisions 0 packets had been deferred Timeslot(s) Used: 1-31默认为31个时隙,成帧R2621 E1-F (不能划分时隙,不能配置,默认1-31时隙捆绑)和R2631E cE1模式对接(划分2个时隙)配置:R2631Econtroller E1 3/0 channel-set 1 timeslot-list 1-15 channel-set 2 timeslot-list 16-31interface Serial3/0:1 link-protocol ppp ip address 5.6.7.8 255.255.255.0 # interface Serial3/0:2 link-protocol ppp R2621无E1-F配置选项interface Serial2 link-protocol ppp ip address 5.6.7.10 255.255.255.0 端口状态显示:R2631Edis int serial 3/0:1 Serial3/0:1 current state :UP Line protocol current state :DOWN Description : Serial3/0:1 Interface The Maximum Transmit Unit is 1500, Hold timer is 10(sec) Derived from E1 3/0, Timeslot(s) Used: 1-15, baudrate is 960000 bps Internet Address is 5.6.7.8/24 Link layer protocol is PPP LCP reqsent Output queue : (Urgent queue : Size/Length/Discards) 0/50/0 Output queue : (Protocol queue : Size/Length/Discards) 0/500/0 Output queue : (FIFO queuing : Size/Length/Discards) 0/75/0 Last 300 seconds input rate 0.00 bytes/sec, 0.00 packets/sec Last 300 seconds output rate 1.20 bytes/sec, 0.06 packets/sec Input: 0 packets, 0 bytes 0 broadcasts, 0 multicasts 40 errors, 0 runts, 0 giants 10 CRC, 0 align errors, 0 overruns 0 dribbles, 3 aborts, 0 no buffers 27 frame errors Output:27 packets, 486 bytes 0 errors, 0 underruns, 0 collisions 0 deferred R2631Edis int serial 3/0:2 Serial3/0:2 current state :UP Line protocol current state :DOWN Description : Serial3/0:2 Interface The Maximum Transmit Unit is 1500, Hold timer is 10(sec) Derived from E1 3/0, Timeslot(s) Used: 16-31, baudrate is 1024000 bps Internet protocol processing : disabled Link layer protocol is PPP LCP stopped Output queue : (Urgent queue : Size/Length/Discards) 0/50/0 Output queue : (Protocol queue : Size/Length/Discards) 0/500/0 Output queue : (FIFO queuing : Size/Length/Discards) 0/75/0 Last 300 seconds input rate 0.00 bytes/sec, 0.00 packets/sec Last 300 seconds output rate 1.13 bytes/sec, 0.06 packets/sec Input: 0 packets, 0 bytes 0 broadcasts, 0 multicasts 56 errors, 0 runts, 0 giants 11 CRC, 0 align errors, 0 overruns 0 dribbles, 1 aborts, 0 no buffers 44 frame errors Output:35 packets, 630 bytes 0 errors, 0 underruns, 0 collisions 0 deferred R2621dis int serial 2 Serial2 current state:up, line protocol current state:down The Maximum Transmit Unit is 1500 Internet Address is 5.6.7.10(24) physical layer is E1-F, baudrate is 1984000 bps Link-protocol is PPP LCP reqsent, IPCP initial, IPXCP initial, CCP initial, BRIDGECP initial Input queue : (size/max/drops) 0/50/0 FIFO queueing: FIFO (Outbound queue:Size/Length/Discards) FIFO: 0/75/0 Last 5 minutes input rate 0.00 bytes/sec, 0.00 packets/sec Last 5 minutes output rate 0.00 bytes/sec, 0.00 packets/sec Input: 5 packets, 45 bytes 0 broadcasts, 0 multicasts 5 errors, 0 runts, 0 giants 5 CRC,0 frame errors, 0 overrunners 0 aborted sequences 0 no buffers 0 packets with dribble condition detected Output:3 packets, 54 bytes 0 broadcasts, 0 multicasts 0 errors, 0 underruns, 0 collisions 0 packets had been deferred Timeslot(s) Used: 1-31 R2631E-E1 3/0clock master %Mar 4 16:19:26 2005 R2631E PHY/2/PHY: Controller E1 3/0: change status to down R2631E-E1 3/0 %Mar 4 16:19:26 2005 R2631E PHY/2/PHY: Serial3/0:1: change status to down %Mar 4 16:19:26 2005 R2631E PHY/2/PHY: Serial3/0:2: change status to down %Mar 4 16:19:26 2005 R2631E PHY/2/PHY: Controller E1 3/0: change status to up %Mar 4 16:19:26 2005 R2631E PHY/2/PHY: Serial3/0:1: change status to up %Mar 4 16:19:27 2005 R2631E PHY/2/PHY: Serial3/0:2: change status to up R2631E-E1 3/0clock slave %Mar 4 16:19:35 2005 R2631E PHY/2/PHY: Controller E1 3/0: change status to down R2631E-E1 3/0 %Mar 4 16:19:35 2005 R2631E PHY/2/PHY: Serial3/0:1: change status to down %Mar 4 16:19:35 2005 R2631E PHY/2/PHY: Serial3/0:2: change status to down %Mar 4 16:19:36 2005 R2631E PHY/2/PHY: Controller E1 3/0: change status to up %Mar 4 16:19:36 2005 R2631E PHY/2/PHY: Serial3/0:1: change status to up %Mar 4 16:19:36 2005 R2631E PHY/2/PHY: Serial3/0:2: change status to up 物理链路都是可以起来. R2621 E1-F (不能划分时隙,不能配置,默认1-31时隙捆绑)和R2631E cE1模式对接(划分1个时隙 1-31)配置:R2631Econtroller E1 3/0 channel-set 0 timeslot-list 1-31 interface Serial3/0:0 link-protocol pppR2621无E1-F配置选项interface Serial2 link-protocol ppp ip address 5.6.7.10 255.255.255.0 端口状态显示R2631Edis int serial 3/0:0 Serial3/0:0 current state :UP Line protocol current state :UP不配置ip地址一样的会协议up Description : Serial3/0:0 Interface The Maximum Tran