外文翻译--举升机

英文原文 Lift Auto lift refers to vehicle repair industry for the lifting of the steam guarantees the equipment. Lift in automobile maintenance and curing plays a very important role, whether the vehicle overhaul, or minor repairs and maintenance, are inseparable from it, and its products have a direct impact on nature and quality maintenance personnel safety. The scale of maintenance and curing enterprises, whether maintenance range of vehicles comprehensive repair shop, or business scope single street shop (such as tire store), almost all equipped with lifting machine. From 1990s, domestic lifting machine gradually became popular in China, with the increase of auto possession, lift as an important tool for car maintenance, demand too greatly increased. Now lift market has nearly 100 Chinese and foreign brand, product series hundreds of thousands. Lift foreign famous brand has bend - Rotary, pak, domestic have antell force, million force AMREOC, jinhua (open JIG), han MaiKeSen, sequence of, yuan levy, so f, extensive force, etc. classification Foreign brands though prices higher, but rely on its product quality, stable performance, the equipment is simple, established in dealers good reputation. As in recent years the development of domestic lifting machine industry, no matter in product design, technical development or after-sales service, were a lot of improvement, sales have greatly improved. Lifting machine according to the function and shapes points, can generally be divided into, two columns, four-column, scissor three categories. use According to the function can be divided into four-wheel location type peace plate； According to occupy space can be divided into the ground type and Tibetan； The ground type, suitable for without any repair mode, some on the floor slabs not suitable to install two column lift and ordinary four-column lift, and the machine and floor surface wide, so you can drive can be installed in any of the floor above, resolve customer site problem. Scissor lift than two columns and four-column lift the biggest advantage is not taking up space, convenient use, the deficiency is fill oil balance is very strict, and the need to have control box, cost is more expensive. Four-column lift product features 1, lift up to maximum lifting height limit a switch can automatically automatically cut off the power of hydraulic pump circuit. 2, powerful high-horsepower motor. 3, lifting ability reach 350 tons. 4, safe and reliable insurance device. 5, practical design. 6, low noise, low vibration design. 7, expanded lift platform width. 8, spacious operation space. 9, 100% prevent cylinders spills. 10, electric hydraulic type second lifting. 11, import reversing valves, manual directional control, electric reversing two models to choose from. Zimu scissor lift product features 1, each lifting machine is equipped with a small cut, this small cut with the Lord with the same hydraulic balance control cut, the maximum lifting height way 400mm ascension. 2, the four-wheel location with high precision. The hydraulic oil cylinder deputy Lord of the way that the system has the following advantages: balance No link rod, work and comfortable, barrier-free, the distance between the running boards can be adjusted freely. 3 and the minimum height, can only 220mm above ground installation for reducing costs. 4, photoelectric switch detection by lifting balanced guarantees vehicle safety. 5 all the oil cylinder, equipment installed explosion-proof valve, prevent oil cylinder failure safety after a sudden decrease guarantee. The worlds first unique inversion oil cylinder two columns lifting machine In response, the independent development of countryside policy motor repair the world first inversion double oil cylinder column lift, the operation is simple, lifting machine of the space is little, the price is cheap, very appropriate in the country with TouJian pits. Lifting machine USES the principal deputy oil cylinder and lifting more stable. Unilateral manual to unlock, operation more convenient. Equipment design is exquisite, convenient installation. Equipment for 2300mm within the span only, saving field. Automatic protection turned arms. Use cross square tube, the strength of the sliding Taiwan increased by 50% or more. Lifting machine adopts maintenance-free sliding sets the slider. Powder painting, surface more luster, more durable, more durable. Lift safety operation procedures A, should remove lift before use near the fixture and sundry hamper operations, and check whether normal operating handles. Second, operating mechanism sensitive effective, hydraulic system are not allowed to have crawled phenomenon. Third, a car, four teams in same plane Angle should, adjust a horn pads height make its contact vehicle chassis support area. Four, a car, not too high, branch of the vehicle team up to lock after four bracket. Five, stay after lifting vehicles should be into lifting machine support block to adjust the model provisions are moving the lifting point. Six, lift at personnel should leave vehicles, lifting to need highly, must insert insurance locking pin, and ensure safe and reliable to start underneath the car homework. Seven, except subsidies and minor repairs project outside, other trival heavy lifter operation that may in the operation of repair. Eight, the lifter not frequent fluctuations. Nine, a car lifting want firm, landing to slow. Ten, someone operations lifting lift is strictly prohibited. Eleven, found that the operator is ineffective, not synchronous motor, bracket uneven or hydraulic parts shall promptly report, leakage of oil, not in spite of operation. Twelve, homework finished should remove debris, clean the lift around to keep site neat. Thirteen, regular (half an year) ruled out lifting oil cylinder seeper, check and the amount of oil, the oil is enough should be timely refill the same brand of pressure oil. At the same time should check lubrication, lift transmission gears and sew bar. Auto four-wheel use method and the matters needing attention One, get on preparatory work before: Tested vehicles driving on lifting machine before, needs to check whether the four wheels tire pressure conforms to the standard tire pressure. Whether badly worn tread pattern. Sure lift two bearing plate width and the tested vehicles before and after the wheelbase in line, then lift troops to its lowest point, ensure corner after the plate and the board after into fixed pin, then will be measured on lifting machine vehicles. Vehicles in lifting machine should be in front, dont make the body to askew. The two front wheel will fall vehicle in two corner, and the center of the disk on the disc to Angle plate in tire uniform distribution of both sides. Vehicle flameout, pull handcuffed brake, shake her left side, window glass driver left vehicles. Operator need forcibly pressure respectively the front and the rear bodywork, to make the vehicle suspension reset. After the installation four during production. Second, installation fixture: According to the test vehicle wheels to adjust size fixture. First LongZhao position, below two adjustment to the right size position, then adjust the length of two card arm out. The first two LongZhao below, in the top of the steel wheel, then raised outside edge, and loosen the LongZhao above the knob, adjust its position, that is also in the top of the steel wheel is raised outside, and then tighten the knob. The next step is to use his hands and promote activity in the fastener rod, to make CARDS in the wheels can card arm, then hang security within the tattoo hook, check fixtures is installed firmly. Three, installation controller is equipped: According to the corresponding four sensors installed to the wheels of the fixture position. Should pay attention to in the positioning shaft sensor to daub sparse of lubricating oil (cannot besmear butter), in order to prevent the long time after insertion caused wear, cant accurate positioning shaft installed in place, affect the measurement precision. Connecting communication cable and Angle to disk cables. The arrow on the cable plug sockets and of the arrow after, you can directly inserted. Four cable length of the difference just is different, the two root 6.5 meters cable is used for connecting controller is equipped with two fronts sensors, two 4.5 meters in the cable is mutual connection. Before and after sensor Each sensor has three socket, above two are the same, the one below is used for connecting corner plates. Cable connection good after, unplug corner after the plate and skateboard fixed pin. Give the vehicle lifting the lowest lift down the safety lock up the grid position, in order to ensure lifting platform in horizontal status. On the sensor and controller is equipped power indicator, press R key or the corresponding position key activation each sensor, after the sensor is put on the level of fixed the knob, tighten the bubble in roughly the level of position. Four, operation controller is equipped: Boot after, batch program will automatically into measurement procedures for users initial status for the next step, the operation. According to move to the next step can be F3 keys. Screen TEST, said that the system was refreshed memories of last measurement information. Then program started measuring steps. Step four main points measuring steps, the first is the measure, including preparation of the input registration forms, select models and deviation of compensation. Input the registration form: contains various customer information, can choose any want to input project, and the future of the project can be according to the input to mix the measurement results data. PaiZhaoHao or maintenance, can generally vehicles single Numbers to enter the corresponding entries for future submitted. Input information can be English letters and Numbers, no Chinese character input. Fill out the form, by F3 after entering models choose interface. Choose the corresponding to the test vehicle models, if need to do after deviation of compensation, then the advance, or press F4 F3 stop. With deviation compensation: if the fixture is used, the only one in rapid fixture serious damage degree when straps, they need to do with deviation compensation (for PassatB5 AudiA6 or before must do, measurement for deviation compensation)； If the use of peeling, the fixture since for all vehicles must do with deviation compensation. Do the deviation of compensation points: (1) tire rotation direction should be vehicles moving direction of rotation. (2) adjustment before detection: installed controller is equipped with brakes locked. Equipment Enter adjustment before detecting steps, steering wheel will appear on the screen to it pattern. In the green area, says acceptable range, but on both sides of the green range around the measurement results, can differ about five points. Therefore, it is best to in the green zone of arrows in the middle in the black. The steering wheel in the order: first, then turn right, then left 20 degrees to 20 degrees, then. Measured at the screen when the front wheel beam. According to measurements F3 button to enter the maximum rotation Angle plate, using electronic steps through the steps the controller is equipped can be automatic measure the maximum total corner. Firstly, then according to the steering wheel in errov screen, remove both front sensor. Stay screen displays the measured, after waiting for picture to the right until the steering wheel continuous play motionless, then a steady living so far not let go. Wait until after continuous measurement to the right, then play the steering wheel so until dozen dont move, and then a steady living not let go. Wait until after the end of automatic measurement, screen showed all the measurement data. Reload the two front sensor, if measured data, adjustable scope of more than allow the data, it can adjust steps into position. Positioning adjustment: do positioning adjustment before, first with a steering wheel lock will steering wheel fixed into horizontal rises again to proper adjustment of lifting machine, will lift high level security position in the lock. Adjusted for four sensors horizontal status, then operate controller is equipped into position adjustment operation. Adjust program will first display vehicles the measured value of the rear axle a parameters, if vehicle rear-axle parameters is adjustable (most vehicles rear-axle positioning parameter is unable to adjust), then the screen can consult to adjust, screen data at the data will display the current adjusted parameters data. Rear-axle positioning parameters adjustment, by F3 after may enter front axle tuning steps. Camber Angle adjustment p-s-n according to the structure of the vehicle chassis, can be divided into two kinds, one kind is need to lift shaft can be adjusted to front wheel impending camber Angle； Another kind is need not lifting front axle camber Angle can be adjusted. The need for lifting the front axle camber Angle adjustment, its position adjustment of vehicle steps as follows: 1) according to the screen F3 key until p-s-n adjust the picture. This screen also showed that the front axle of the five positioning parameter values, they were: left, right wheel, left, right, camber Angle front wheel bundle, total before former beam. Then press F7 keys, screen SVRMGR , hints you now can use second lifter will lift the front axle vehicles. In your vehicle with secondary lifting will lift shaft, then press F3 key after going forward, this screen camber Angle data right wheels. Now you can according to the screen display camber Angle adjustment data. 2) adjust the left, right after the camber Angle, wheel, then according to the F3 keys on the screen can now will be second lifting down clew, right now can put down second lifting, when vehicles in lift platform front fell steadily honked vehicle front axle after the suspension parts, down a few times, to make the vehicle suspension reset p-s-n. Vehicles put good, then press, when screen F3 keys back on the front axle adjust the picture. 3) can now, adjust the picture in front of the left and right according to show about former bunch of value adjustment round wheels. Before bundle When former bundles and a total right wheels are well adjusted before beam and press F4 keys end positioning adjustment process. 4) to need not lifting front axle camber Angle adjustment, then can the vehicle in front axle, adjust the picture camber Angle adjustment according to the first, and then the order and beam before adjust reference screen real-time display, the parameters of the value adjusted respectively camber Angle, or so ago about values. Bundle Adjusted by F4, after adjustment process end positioning. Adjusted to detect: lifting when measuring the troops back to adjust the height of before, will lift the lock in horizontal safe place. Enter adjusted, when measured steps showed on the screen of the two front current value. Before alone bundle According to the remaining steps forward, F3 adjustment before testing steps with same. If on the steps of the two front wheel display before alone adjustment process and the position of the beam value in former bunch of value adjustment good have bigger difference, the reason probably because in after adjustment, the process of vehicle fell down, the steering wheel position changed, killing the two front wheel position change. So each wheel alone with former bunch of value orientation for the adjustment of different values, but front wheel wont change. Total former bundle But because after adjusting when entering test shown before the front wheel of single beam value will be record and the final measurement results, which makes the displayed in the front wheels alone adjustment results report before may bundle value unqualified. But the reality is front wheel always is qualified, former beam steering wheel not only because to former bunch of value in allowing alone outside its range. To prevent this appear, in adjusted, if found in measuring steps each wheel shown before alone adjustment and the position of the beam value is not the same as the value, according to a larger F3 forward, to the screen in until after the steering wheel in here is on, steering wheel. Then press F4 key exit after adjusting the detecting steps, then re-enter adjusted detecting steps. Right now because of the previous step to the steering wheel, so should be displayed on the screen of the steering wheel in cases before beam value, the value of just what we need. If former bunch of value in the permissible, indicates that location adjustment qualified, if the former bunch of value is still not qualified, indicates that a step up positioning adjustment is not ready, still need to be adjusted step back to the positioning again again adjustments. Finally shows measurement adjustment results are given statements adjustment before measured values, and the measured value standard after adjusting to adjust for after the final result measurements. Therefore, if the measurements, after adjusting the parameters of the existing can adjust the data is unqualified, it will need to return to the localization tuning steps to adjust. To move the cursor moves to measure the printer icon adjustment results statements position, then press the return key confirmed that can print a complete measuring adjustment results report. After printing, the measured results will be preserved for later can shifting gear query. If not print, then measured results data would be lost. If you want to save the measurement data, and dont want to print, can be in print before closing printer, again printing operations. The system will automatically generate printed documentation, then switch printers, if the system found printer is closed and error will appear on the screen, dont worry, this measurement results have been preserved. 中文译文 举升机 汽车举升机是指汽车维修行业用于汽车举升的汽保设备 。举升机在汽车维修养护中发挥着至关重要的作用，无论整车大修，还是小修保养，都离不开它，其产品性质、质量好坏直接影响维修人员的人身安全。在规模各异的维修养护企业中，无论是维修多种车型的综合类修理厂，还是经营范围单一的街边店（如轮胎店），几乎都配备有举升机。 汽车举升机是指汽车维修行业用于汽车举升的汽保设备。举升机在汽车维修养护中发挥着至关重要的作用，无论整车大修，还是小修保养，都离不开它，其产品性质、质量好坏直接影响维修人员的人身安全。在规模各异的维修养护企业中，无论是维修多种车型的综合类修理厂，还是经营 范围单一的街边店（如轮胎店），几乎都配备有举升机。 从 20 世纪 90 年代开始，国内举升机逐渐开始普及，随着我国汽车保有量的增加，举升机作为汽车维修的重要工具，需求量也大大增加。现在举升机市场已经拥有近百个中外品牌，产品系列成百上千。 举升机国外著名的品牌有 bend-pak， Rotary 等，国内有安特力、万力开 AMREOC、金华（ JIG）、汉麦克森、序达、元征、鳌福、广力等。 分类 国外品牌尽管价格较高，但依靠其产品质量好、性能稳定、设备操作简单，在经销商中建立了良好的口碑。随着近几年国内举升机行业的发 展，无论在产品设计、技术开发还是售后服务方面，都进行了很多的改进，销量也大大提高。 举升机按照功能和形状来分，一般可分为，两柱，四柱，剪式三大类。 用途 按照功能可分为四轮定位型和平板式；按照占用的空间不同可分为地上式和地藏式；地上式无需挖槽，适用于任何修理厂，有一些楼板上不适合安装二柱举升机以及普通四柱举升机，而本机器与楼板接触面广，这样可以安装在任何可以开车的楼板上面，解决客户场地问题。剪式举升机比两柱和四柱举升机最大的好处是不占用空间，方便使用，不足之处则是补油平衡要求很严格，而且需配备控制箱， 造价较贵。 四柱举升机产品特点 1、举升机上升到最大举升高度时限位开关会自动断电、自动切断液压泵里的油压回路。 2、大马力的强有力电机。 3、举升能力达到 3.5 吨。 4、安全可靠的保险装置。 5、实用性设计。 6、低噪音，低振动设计。 7、扩大的升降台宽度。 8、宽敞的作业空间。 9、 100%防止油压缸漏油。 10、电动液压式二次举升。 11、进口换向阀、手动换向、电动换向 两种机型可供选择。 子母剪式举升机产品特点 1、每个举升机配备一个小剪，该小剪用与主剪相同的液压平衡控制方式，最大举升高度提升 400mm。 2、可配置高精密的四轮定位。主副油缸的液压方式保证系统的平衡，具有以下优点： 无连接杆，工作舒适，无障碍，跑板间距离可随意调整。 3、本机最低高度仅为 220mm，可地面安装减少费用。 4、可通过光电开关检测举升是否平衡，可保证车辆安全。 5、设备上所有油缸都安装了防爆阀，防止油缸失效后突然下降保证人身安全。 世界首创独一无二的倒置油缸两 柱举升机 ECO1122 为响应汽修下乡政策，独立开发的世界首创倒置油缸双柱举升机，本举升机操作简单，占空间小，价格低廉，非常合适在乡村投建维修站用。 举升机采用主副油缸，升降更加平稳。 单边手动解锁，操作更方便。 设备设计精巧，安装方便。 设备内跨距仅为 2300mm，节约场地。 自动防转支臂。 使用十字方管，滑台的强度提高 50%以上。 举升机采用免保养的滑台滑块。 粉末烤漆，表面更 光泽、更持久、更持久。 举升机安全使用操作规程 一、使用前应清除举升机附近妨碍作业的器具及杂物，并检查操作手柄是否正常。 二、操作机构灵敏有效，液压系统不允许有爬行现象。 三、支车时，四个支角应在同一平面上，调整支角胶垫高度使其接触车辆底盘支撑部位。 四、支车时，车辆不可支的过高，支起后四个托架要锁紧。 五、待举升车辆驶入后，应将举升机支撑块调整移动对正该车型规定的举升点。 六、举升时人员应离开车辆，举升到需要高度时，必须插入保险锁销，并确保安全可靠才可开始车底作业。 七、除低保及小修项目外，其他繁琐笨重作业，不得在举升器上操作修理。 八、举升器不得频繁起落。 九、支车时举升要稳，降落要慢。 十、有人作业时严禁升降举升机。 十一、发现操作机构不灵，电机不同步，托架不平或液压部分漏油，应及时报修，不得带病操作。 十二、作业完毕应清除杂物，打扫举升机周围以保持场地整洁。 十三、定期（半年）排除举升机油缸积水，并检查油量，油量不足应及时加注相同牌号的压力油。同时应检查润滑、举升机传动齿轮及缝条。 汽车四轮定位仪的使用方法及注意事项 一、 上车前准备工作： 在被测车辆开上举升机之前，需要检查四个车轮的胎压是否符合标准胎压。轮胎花纹是否严重磨损。确定举升机两个承载板的宽度与被测车辆的前、后轴距一致，然后将举升机降至最低点，确保转角盘和后滑板的固定销都插好之后，再将被测车辆开上举升机。车辆在举升机上应处于正前方向，不要使车身歪斜。车辆的两前轮要落在两转角盘的中心上，同时转角盘的圆盘要均匀分布在轮胎的两侧。车辆熄火后，拉上手刹，摇下左前侧车窗玻璃，司机离开车辆。操作员需要分别用力压车身的前部和后部，以使车辆的悬挂复位。之后是安装四个卡具。 二、安装卡具： 根据所测车辆的车轮尺寸对卡具进行调整。首先调整下方两个尼龙爪位置到合适的尺寸位置，然后调节两个卡臂的伸出长度。先将下方的两个尼龙爪顶在钢圈的凸起的外沿，然后再松开上方尼龙爪的旋钮，调整它的位置，使之也顶在钢圈的凸起的外沿，然后再拧紧旋钮。下一步是用两手同时推动卡具上的活动杆，使卡臂能够卡在轮纹内，然后挂上安全钩，检查卡具是否安装牢固。 三、安装定位仪： 将四个传感器按照对应车轮的位置安装到卡具上。要注意在传感器的定位轴上要涂抹稀的润滑油（不能涂黄油），以防止长时间插拔后 造成定位轴磨损，无法准确安装到位，影响测量精度。连接通讯电缆和转角盘电缆。把电缆插头上的箭头和插座上的箭头标记对好之后，就可以直接插入。四根电缆的差别只是长度不同，两根 6.5 米的电缆是用来连接定位仪和两个前轮上的传感器，两个 4.5 米的电缆是在前后传感器之间互相连接。每个传感器上有 3个插座，上面两个是完全一样的，最下面的一个是用来连接转角盘。电缆连接好之后，拔掉转角盘和后滑板上的固定销。将车辆举升后落到举升机最低一格的安全锁止位置，以保证举升平台处在水平状态。定位仪开机，传感器上的电源指示灯亮，按 R 键或相应的 位置键激活各个传感器，把传感器上放水平后拧紧固定旋钮，水平气泡处在大致中央的位置。 四、操作定位仪： 开机之后，批处理程序会自动进入测量程序的初始状态，等待用户进行下一步的操作。按 F3 键可前进到下一步。屏幕上出现“ TEST”，表示系统正在刷新所记忆的上次测量的信息。然后程序开始测量步骤。测量步骤主要分四步，首先是测量前的准备工作，包括输入登记表格，选择车型和偏位补偿。输入登记表格：包含了各项客户信息，可以任意选择要输入的项目，并且将来可以根据所输入的项目来调出